15
Jan
Plastic tweezers come in handy for this. A standard IDE cable will have two connectors on it for the 2 IDE devices.
However you need to check the jumper configuration for the exact model drive you have.
Ide hard drive jumper. These pins are called jumpers and are used to enable specific types of settings. Theyre not used so much with modern hard drives except in some special circumstances. If youre under a certain age or you just havent been into computer hardware for long youve probably never heard of hard drive jumpers.
The jumper pins are similar to the pins on the IO plate on a motherboard. If you ever have ever had to replace an IDE hard drive or CDDVD drive for that matter you may have noticed that there are jumper settings that have to be set to make the computer recognize the drive correctly. A standard IDE cable will have two connectors on it for the 2 IDE devices.
Some cables may only come with one though. The slave drive does not rely on the master drive for its operation or vice versa. Its just used so the computer knows which drive to send data to.
First set the jumpers if it is an IDE drive. Lets talk about this in more detail because most people have IDE drives. In the IDE system most motherboards allow you to have two IDE cables.
Each cable can connect to two drives. Usually you use one cable to connect one or two optical drives to your machine. The drive is the first drive to be used on the cablechannel connected to the end connector on an IDE cable.
The Jumper pin order of a CD rom or hard drive is usually written somewhere on the drive. It could be at the back like in the picture below or it could be on the top or sides. Simply connect the drive to the black connector at the end of the cable.
Installing the new drive as the primary Master drive. If you are connecting your drive as the primary drive on the cable with another IDE drive there is no need to change the jumper pin on the drive. Jumper the other IDE drive as Cable Select.
Know how to Setup jumper setting in just few secondsExplained clearly how to do. New hard drives or used hard drives that have had their partitions deleted have NO DATA on them and will not appear as one or more drive letters in Computer or Windows Explorer. You must go to Control Panel - display as Small Icons or Large Icons not Category - Administrative Tools - Computer Management - Disk Management - and make at least one partition on it and format the partitions.
Master or single drive. If you are installing your Seagate hard drive as the only drive in the system or if it will be the primary boot drive for the system the jumper should be set as Cable Select. If you are connecting the drive to an older system that has a pre-UDMA Mode 3 ATA controller or you are connecting this to a cable with a slave device that doesnt have a cable select jumper setting jumper the drive as Master instead by putting a jumper on the first vertical set of pins.
Setting the Jumpers Master or Single Drive - Use this setting if the drive is the only drive on the ATA interface cable. Drive is Slave - Use this setting if the drive is an additional drive on the cable and the original drive is set as Master. Connect the drive using the Master connector on the primary IDE cable.
Set the second hard disk jumper to Slave use the Cable Select selection if Cable Select was set on the first hard drive. Connect the drive using the Slave connector on the primary IDE cable. Set the CDDVD drive jumper as Cable Select.
Now many 25 drives do have an extra 4 jumper pins that are normally uncovered and their typical purpose is to force a drive into IDE master or slave mode. However you need to check the jumper configuration for the exact model drive you have. A jumper may also be referred to as a jumper shunt or shunt.
Jumpers manually configure computer peripherals such as the motherboard hard drives modems sound cards and other components. For example if your motherboard supported intrusion detection a jumper can be set to enable or disable this feature. To begin with you need to understand that in a standard internal configuration of IDE hard drives the jumper settings are used to determine the order in which hard drives and other devices such as.
Jumper the Hitachi drive as Device 1 SLAVE. Attach the Cables Note. With some system cases it may be easier to attach the cables after the drive is mounted in the system.
Attach the blue connector of the ATA IDE cable to the IDE connector marked Primary or 0 on the motherboard or controller card in your system. Attach a power cable to the hard disk drive. Buy Ide Hard Drive Cable and get the best deals at the lowest prices on eBay.
Great Savings Free Delivery Collection on many items. The jumpers usually are white black or blue in color. The pin settings are printed on the drives label on its logic board as in this picture or both.
To bridge a connection you slide a jumper over the corresponding pins as in this picture. Plastic tweezers come in handy for this. Seagate 35 Internal IDE Hard Drive ST340014A 5JXD1Y94 Windows 7 Pro 64bit 5 out of 5 stars 9 9 product ratings - Seagate 35 Internal IDE Hard Drive ST340014A 5JXD1Y94 Windows 7 Pro 64bit.